Implications of Vertical Stability Control on the SPARC Tokamak
Fuente:
arXiv
Guardado en:
| Autores principales: | , , , , , , , |
|---|---|
| Formato: | Preprint |
| Publicado: |
2024
|
| Materias: | |
| Acceso en línea: | |
| Etiquetas: |
Agregar Etiqueta
Sin Etiquetas, Sea el primero en etiquetar este registro!
|
| _version_ | 1866929214025891840 |
|---|---|
| author | Nelson, A. O. Garnier, D. T. Battaglia, D. J. Paz-Soldan, C. Stewart, I. Reinke, M. Creely, A. J. Wai, J. |
| author_facet | Nelson, A. O. Garnier, D. T. Battaglia, D. J. Paz-Soldan, C. Stewart, I. Reinke, M. Creely, A. J. Wai, J. |
| contents | To achieve its performance goals, SPARC plans to operate in equilibrium configurations with a strong elongation of $κ_\mathrm{areal}\sim1.75$, destabilizing the $n=0$ vertical instability. However, SPARC also features a relatively thick conducting wall that is designed to withstand disruption forces, leading to lower vertical instability growth rates than usually encountered. In this work, we use the TokSyS framework to survey families of accessible shapes near the SPARC baseline configuration, finding maximum growth rates in the range of $γ\lesssim100\,$s$^{-1}$. The addition of steel vertical stability plates has only a modest ($\sim25\%$) effect on reducing the vertical growth rate and almost no effect on the plasma controllability when the full vertical stability system is taken into account, providing flexibility in the plate conductivity in the SPARC design. Analysis of the maximum controllable displacement on SPARC is used to inform the power supply voltage and current limit requirements needed to control an initial vertical displacement of $5\%$ of the minor radius. From the expected spectra of plasma disturbances and diagnostic noise, requirements for filter latency and vertical stability coil heating tolerances are also obtained. Small modifications to the outboard limiter location are suggested to allow for an unmitigated vertical disturbance as large as $5\%$ of the minor radius without allowing the plasma to become limited. Further, investigations with the 3D COMSOL code reveal that strategic inclusion of insulating structures within the VSC supports are needed to maintain sufficient magnetic response. The workflows presented here help to establish a model for the integrated predictive design for future devices by coupling engineering decisions with physics needs. |
| format | Preprint |
| id |
arxiv_https___arxiv_org_abs_2401_09613 |
| institution | arXiv |
| publishDate | 2024 |
| record_format | arxiv |
| spellingShingle | Implications of Vertical Stability Control on the SPARC Tokamak Nelson, A. O. Garnier, D. T. Battaglia, D. J. Paz-Soldan, C. Stewart, I. Reinke, M. Creely, A. J. Wai, J. Plasma Physics To achieve its performance goals, SPARC plans to operate in equilibrium configurations with a strong elongation of $κ_\mathrm{areal}\sim1.75$, destabilizing the $n=0$ vertical instability. However, SPARC also features a relatively thick conducting wall that is designed to withstand disruption forces, leading to lower vertical instability growth rates than usually encountered. In this work, we use the TokSyS framework to survey families of accessible shapes near the SPARC baseline configuration, finding maximum growth rates in the range of $γ\lesssim100\,$s$^{-1}$. The addition of steel vertical stability plates has only a modest ($\sim25\%$) effect on reducing the vertical growth rate and almost no effect on the plasma controllability when the full vertical stability system is taken into account, providing flexibility in the plate conductivity in the SPARC design. Analysis of the maximum controllable displacement on SPARC is used to inform the power supply voltage and current limit requirements needed to control an initial vertical displacement of $5\%$ of the minor radius. From the expected spectra of plasma disturbances and diagnostic noise, requirements for filter latency and vertical stability coil heating tolerances are also obtained. Small modifications to the outboard limiter location are suggested to allow for an unmitigated vertical disturbance as large as $5\%$ of the minor radius without allowing the plasma to become limited. Further, investigations with the 3D COMSOL code reveal that strategic inclusion of insulating structures within the VSC supports are needed to maintain sufficient magnetic response. The workflows presented here help to establish a model for the integrated predictive design for future devices by coupling engineering decisions with physics needs. |
| title | Implications of Vertical Stability Control on the SPARC Tokamak |
| topic | Plasma Physics |
| url | https://arxiv.org/abs/2401.09613 |