Open-Source Software Architecture for Multi-Robot Wire Arc Additive Manufacturing (WAAM)

Configuration-Dependent Robot Kinematics Model and Calibration
par: Lu, Chen-Lung, et autres
Publié: (2025)

Practical Guidelines for Wire Arc Additive Manufacturing of Steel Components
par: Nicolas Hadjipantelis
Publié: (2025)

Fabrication and Characterization of Nickel‐Aluminide Cladding by Dual‐Wire Arc Additive Manufacturing
par: Navid Samadi, et autres
Publié: (2024)

Carbon Footprint of Wire Arc Additively Manufactured Optimized Structural Steel Element
par: Lidiana Arrè, et autres
Publié: (2025)

Flexural Buckling Behavior of Wire‐Arc Additively Manufactured Stainless Steel Bars
par: Vittoria Laghi, et autres
Publié: (2025)

Radial Deposition for Mechanical Bonding of Dissimilar Metals in Wire Arc Additive Manufacturing
par: Lile Squires, et autres
Publié: (2025)

Tribological Behavior of Wire Arc Additively Manufactured 2219 Aluminum Alloy in Vacuum
par: Bin Shao, et autres
Publié: (2025)

Experimental and Numerical Investigation of Mechanical and Geometric Properties of Wire Arc Additively Manufactured Structures
par: Pouya Afshar Imani, et autres
Publié: (2025)

A New Generation of Lattice Structural Elements Produced with Wire‐Arc Additive Manufacturing
par: Vittoria Laghi, et autres
Publié: (2025)

Effect of Design Parameters on Residual Stresses in Plates Stiffened by Wire and Arc Additive Manufacturing
par: Anjusha K V, et autres
Publié: (2025)

Stub Column Tests on Concrete‐Filled Wire Arc Additively Manufactured Steel Tubes
par: Wenxuan Hong, et autres
Publié: (2025)

Study on Anisotropic Design Method for Pipe Connection Flanges Based on Wire Arc Additive Manufacturing
par: Xiaoben Chen, et autres
Publié: (2025)

Hybrid Statistical Process Monitoring of Wire Arc Additive Manufacturing With Frequency‐Informed Deep Learning
par: Giulio Mattera, et autres
Publié: (2025)

Microstructure and Mechanical Properties of Bimetallic Structure Fabricated through Wire Plus Arc Additive Manufacturing
par: Vijayakumar Murugesan Devarajan, et autres
Publié: (2024)

Additively Manufactured Open-Source Quadruped Robots for Multi-Robot SLAM Applications
par: Fuge, Zachary, et autres
Publié: (2024)

Microstructure and Hot Oxidation Resistance of Wrought and Wire Arc Additive Manufactured Austenitic Stainless Steel 347
par: Arasappan Rajesh Kannan, et autres
Publié: (2024)

Local Buckling Behaviour of Wire Arc Additively Manufactured High Strength Steel Circular Hollow Sections
par: Wenxuan Hong, et autres
Publié: (2025)

Thermodynamic Pathways of Nonequilibrium Solidification in Wire‐Arc Additive Manufacturing Fe‐Based Multicomponent Alloy Structures
par: Blanca Palacios, et autres
Publié: (2026)

Alertness Optimization for Shift Workers Using a Physiology-based Mathematical Model
par: Tao, Zidi, et autres
Publié: (2026)

New Developments in the Field of Production and Application of Multi‐Material Wire Arc Additive Manufacturing Components: A Review
par: Kai Treutler, et autres
Publié: (2025)

Effects of Post‐Weld Heat Treatments on the Microstructure and Residual Stresses of Wire Arc Additive Manufactured Magnesium Alloy
par: S. Goka, et autres
Publié: (2025)

Mechanical Testing and Microstructural Characterization of Bimetallic Structure of Austenitic Steel Fabricated via Wire plus Arc Additive Manufacturing
par: Dhinakaran Veeman, et autres
Publié: (2025)

Effect of Travel Speed on Microstructure Evolution of Cold Metal Transfer with Pulse Wire Arc Additive Manufacturing AA2024
par: Zhiqiang Zhang, et autres
Publié: (2025)

Effect of Titanium Alloying on the Performance of HSLA Steel Cladding on Low‐Carbon Steel via Wire Arc Additive Manufacturing
par: Kumar Kanishka, et autres
Publié: (2025)

Influence of Arc Voltage and Travel Speed on the Environmental Footprint of WAAM: An Experimental LCA Approach
par: Kiana Arteshyar 1, Hossein Feiz Arefy 1, Mohammad Ebadi Tavallaei 1, Kiarash Rahimi 1, Fateme Amini 1, Amirreza Banejad 2, Farhad Kolahan1*
Publié: (2025)

Effect of Aging Treatment on the Interfacial Behavior and Microstructure Characteristics of Babbitt Alloy/Steel Interfaces Fabricated by Wire Arc Additive Manufacturing
par: Geng Wang, et autres
Publié: (2025)

Optimizing Microstructure of Cold Metal Transfer‐Wire Arc Additive Manufactured ER2594 Super Duplex Stainless Steel through a Novel Active Cooling Technique
par: Guang Yang, et autres
Publié: (2025)

Effect of Wire Feed Speed on Microstructure and Mechanical Properties of 205C Aluminum Alloy in CMT+P‐Based Arc Additive Manufacturing
par: Peng Yin, et autres
Publié: (2026)

Optimization of Forging Parameters for Enhanced Mechanical Properties of Wire Arc Additive Manufacturing‐Deposited High‐Strength Low‐Alloy Steel Bead
par: Joshua Lee Jet Wei, et autres
Publié: (2025)

Optimization of Process Parameters to Minimize Porosity and Splash in Cold Metal Transfer and Pulse Wire Arc Additive Manufacturing of High‐Strength Aluminum Alloy
par: Zhiqiang Zhang, et autres
Publié: (2025)

Wire Arc Additive Manufacturing of High‐Strength Al4043 Parts Using TiN and La 2 O 3 as Grain Refiners
par: Simran Nath, et autres
Publié: (2026)

Influence of Graphene‐Based Flux Interlayers on the Microstructure and Properties of Low‐Alloy Steel Fabricated by Cold Metal Transfer‐Based Wire Arc Additive Manufacturing
par: Vivek Babu, et autres
Publié: (2026)

Interfacial Microstructure and Mechanical Properties of Ti‐6Al‐4V/Ni‐Ti Bimetallic Structures Fabricated by Multi‐Wire Arc Additive Manufacturing
par: Mengmeng Xie, et autres
Publié: (2025)

Recent Research on the Modelling and Reliability of Wire‐arc Additively Manufactured Steel Structures
par: Pouya Afshar Imani, et autres
Publié: (2025)

Optimisation of Hybrid WAAM Tubular T‐joints
par: Tong Hu, et autres
Publié: (2025)

An Open-Sourced, Community-Driven Volumetric Additive Manufacturing Printer and Post-Processor
par: Waddell, Taylor, et autres
Publié: (2025)