Image de couverture de livre

Laser fabrication of Ti stent and facile MEMS flow sensor integration for implantable respiration monitoring

Fuente: arXiv

Enregistré dans:

Détails bibliographiques
Auteurs principaux:	Farisi, Muhammad Salman Al, Kawata, Takuya, Hasegawa, Yoshihiro, Zukri, Mohammad Nizar Mohamed, Matsushima, Miyoko, Kawabe, Tsutomu, Shikida, Mitsuhiro
Format:	Preprint
Publié:	2025
Sujets:	Instrumentation and Detectors
Accès en ligne:	Acceder al recurso
Tags:	Ajouter un tag Pas de tags, Soyez le premier à ajouter un tag!

Documents similaires

Single-step laser patterning and thinning of biocompatible MEMS flow sensor
par: Zukri, Mohammad Nizar Mohamed, et autres
Publié: (2025)

Investigation of Calibration Methodology Using Mouth Airflow for Wearable Sensor Toward Quantitative Respiration Monitoring
par: Kenta Horie, et autres
Publié: (2024)

Pitot Tube Sensor Probe System for Simultaneous Airflow and Pressure Measurement of Expiration Inside Pulmonary Airway
par: Aoi Miyawaki, et autres
Publié: (2024)

Hybrid optical sensor for combined thermal and dimensional monitoring in laser processing
par: Donadello, Simone
Publié: (2024)

Three robust temperature-drift compensation strategies for a MEMS gravimeter
par: Valenzuela, Victor M., et autres
Publié: (2024)

Electronics-free passive ultrasonic communication link for deep-tissue sensor implants
par: Yener, Umut Can, et autres
Publié: (2024)

MEMSDuino: An Arduino-Based MEMS Switch Controller
par: Spietz, Lafe, et autres
Publié: (2025)

Design and performance of the prototype gaseous beam monitor with GEM and pixel sensors for the CSR external-target experiment
par: Wang, Hulin, et autres
Publié: (2025)

Development of a real-time beam profile monitor for GeV photons and its application in accelerator facilities
par: Kino, Ryoko, et autres
Publié: (2024)

Designing electrostatic MEMS-based electron optics: the case of the spiral phase plate
par: Kavkani, Payam Habibdazeh, et autres
Publié: (2026)

Model-derived conversion formula for real-time gas monitoring based on chemiresistive sensors
par: Fernandes, Fernando Massa, et autres
Publié: (2026)

Detection of MEMS Acoustics via Scanning Tunneling Microscopy
par: Elbertse, R. J. G., et autres
Publié: (2026)

A flexible test facility for liquid xenon detector development
par: Angelico, Evan, et autres
Publié: (2025)

Performance evaluation of electron multiplier tubes as a high-intensity muon beam monitor of accelerator neutrino experiments
par: Honjo, Takashi, et autres
Publié: (2024)

The CRAB facility at the TU Wien TRIGA reactor: status and related physics program
par: Abele, H., et autres
Publié: (2025)

Characterisation of a low-momentum high-rate muon beam monitor for the FAMU experiment at the CNAO-XPR beam facility
par: Rossini, Riccardo, et autres
Publié: (2023)

Advanced fabrication process for particle absorbers of highly pure electroplated gold for microcalorimeter applications
par: Müller, Michael, et autres
Publié: (2024)

Design, fabrication and initial test of a novel 3D-Trench sensor utilizing 8-inch CMOS compatible technology
par: Liu, Manwen, et autres
Publié: (2024)

Next Generation Multi-element monolithic Germanium detectors for Spectroscopy: First integration at ESRF facility
par: Goyal, N., et autres
Publié: (2025)

Operating a large-diameter dual-phase liquid xenon TPC in the unshielded PANCAKE facility
par: Müller, Julia, et autres
Publié: (2026)

About using of a compact supermirror transmission polarizer in the neutron research facilities of the PIK reactor
par: Syromyatnikov, V. G.
Publié: (2024)

Materials research for hiper laser fusion facilities: chamber wall, structural material and final optics
par: Alvarez, J., et autres
Publié: (2024)

Low-vibration cryogenic test facility for next generation of ground-based gravitational-wave observatories
par: Kapasi, D. P., et autres
Publié: (2024)

Kinetic inductance current sensor for visible to near-infrared wavelength transition-edge sensor readout
par: Szypryt, Paul, et autres
Publié: (2024)

High-yield fabrication of micromirror templates via feedback-controlled laser ablation
par: Allepuz-Requena, Daniel, et autres
Publié: (2026)

Characterisation and simulation of stitched CMOS strip sensors
par: Davis, Naomi, et autres
Publié: (2024)

Correcting the Energy-Dependent Asymmetry in Low-Energy $μ$SR
par: Janka, G., et autres
Publié: (2026)

Depolarization studies on low-depolarizing Cu/Ti and Ni(Mo)/Ti neutron supermirrors
par: Gómez-Guzmán, Jose Manuel, et autres
Publié: (2025)

Advancing optical imaging systems with digital fabrication
par: Wenzel, Tobias, et autres
Publié: (2026)

Simulation of charge transport at the surface of planar silicon sensors
par: Bloch, Ingo, et autres
Publié: (2025)

Comparison calibration system for digital-output infrasound sensors
par: Hirano, Koto, et autres
Publié: (2025)

Smart Pixels: In-pixel AI for on-sensor data filtering
par: Parpillon, Benjamin, et autres
Publié: (2024)

Simulation of radiation environment for the beam monitor of CEE experiment
par: Wang, Qian, et autres
Publié: (2025)

Characterisation and Monte Carlo validation of a compact AmBe neutron irradiation facility providing fast and thermal neutron fields for detector development
par: Bevan, A. J., et autres
Publié: (2026)

Enhancing Aeroacoustic Wind Tunnel Studies through Massive Channel Upscaling with MEMS Microphones
par: Ernst, Daniel, et autres
Publié: (2024)

Reducing suspension control noise with interferometric sensors -- an experimental concept
par: Weickhardt, Nils Leander, et autres
Publié: (2025)

Performance of USTC first batch resistive AC-LGAD sensor
par: Li, Han, et autres
Publié: (2025)

Integration of high-performance compact interferometric sensors in a suspended interferometer
par: Mitchell, Alexandra, et autres
Publié: (2024)

Wavelength-tunable femtosecond pulsed laser for the characterisation of solid-state sensors
par: Ejopu, Enoch, et autres
Publié: (2025)

Recent test beam results of ATLAS ITk Pixel sensors and modules
par: Schmier, A., et autres
Publié: (2026)