Decoupling dislocation multiplication and velocity effects in metals at extreme strain rates
Fuente:
arXiv
Gespeichert in:
| Hauptverfasser: | , , , , , , |
|---|---|
| Format: | Preprint |
| Veröffentlicht: |
2026
|
| Schlagworte: | |
| Online-Zugang: | |
| Tags: |
Tag hinzufügen
Keine Tags, Fügen Sie den ersten Tag hinzu!
|
| _version_ | 1866914425867337728 |
|---|---|
| author | Syrlybayev, Daniyar Raman, Lavanya Atale, Niraj Pramod Maheswaran, Bhanugoban Pathak, Siddhartha Bronkhorst, Curt A. Thevamaran, Ramathasan |
| author_facet | Syrlybayev, Daniyar Raman, Lavanya Atale, Niraj Pramod Maheswaran, Bhanugoban Pathak, Siddhartha Bronkhorst, Curt A. Thevamaran, Ramathasan |
| contents | The dynamic behavior of metals is governed by collective dislocation motion and interactions that strongly depend on the applied strain rate. Metals exhibit weak strain rate sensitivity (SRS) below a certain threshold, followed by a distinct SRS upturn at higher loading rates. While this upturn is typically attributed to increased glide resistance at high dislocation velocity due to mechanisms such as phonon drag, the role of strain-rate-dependent dislocation multiplication and microstructural evolution under these extreme conditions remains elusive. Here, we decouple these two strengthening effects and show that, while dislocation velocity primarily governs the SRS upturn, the hardening due to microstructure evolution depends strongly on the initial dislocation density. Our investigation of hardness evolution across ten decades of strain rates in a quenched and tempered martensitic low-carbon steel (LCS) using laser-induced projectile impact tests (LIPIT) and nanoindentation reveals SRS upturn around 10^7 1/s. By performing in situ re-indentation of the formed craters, we probe the contribution of dislocations generated during initial deformation at different strain rates. We show that while dislocation multiplication plays a negligible role in fine-grained LCS with high dislocation density, a pronounced dislocation multiplication contributes to the hardness increase in pure iron with lower initial dislocation density. Our results show that, depending on the initial microstructure of metals, dislocation multiplication significantly governs high-strain-rate plasticity, in addition to dislocation velocity effects. |
| format | Preprint |
| id |
arxiv_https___arxiv_org_abs_2603_25849 |
| institution | arXiv |
| publishDate | 2026 |
| record_format | arxiv |
| spellingShingle | Decoupling dislocation multiplication and velocity effects in metals at extreme strain rates Syrlybayev, Daniyar Raman, Lavanya Atale, Niraj Pramod Maheswaran, Bhanugoban Pathak, Siddhartha Bronkhorst, Curt A. Thevamaran, Ramathasan Materials Science The dynamic behavior of metals is governed by collective dislocation motion and interactions that strongly depend on the applied strain rate. Metals exhibit weak strain rate sensitivity (SRS) below a certain threshold, followed by a distinct SRS upturn at higher loading rates. While this upturn is typically attributed to increased glide resistance at high dislocation velocity due to mechanisms such as phonon drag, the role of strain-rate-dependent dislocation multiplication and microstructural evolution under these extreme conditions remains elusive. Here, we decouple these two strengthening effects and show that, while dislocation velocity primarily governs the SRS upturn, the hardening due to microstructure evolution depends strongly on the initial dislocation density. Our investigation of hardness evolution across ten decades of strain rates in a quenched and tempered martensitic low-carbon steel (LCS) using laser-induced projectile impact tests (LIPIT) and nanoindentation reveals SRS upturn around 10^7 1/s. By performing in situ re-indentation of the formed craters, we probe the contribution of dislocations generated during initial deformation at different strain rates. We show that while dislocation multiplication plays a negligible role in fine-grained LCS with high dislocation density, a pronounced dislocation multiplication contributes to the hardness increase in pure iron with lower initial dislocation density. Our results show that, depending on the initial microstructure of metals, dislocation multiplication significantly governs high-strain-rate plasticity, in addition to dislocation velocity effects. |
| title | Decoupling dislocation multiplication and velocity effects in metals at extreme strain rates |
| topic | Materials Science |
| url | https://arxiv.org/abs/2603.25849 |