Imagen de Portada

Burr formation and control for polymers micro-milling: A case study with vortex tube cooling

Fuente: Redalyc

Guardado en:

Detalles Bibliográficos
Autor principal:	Michael Miranda-Giraldo
Formato:	Artículo científico
Lenguaje:	en
Publicado:	Universidad Nacional de Colombia 2017
Materias:	Ingeniería Burr Micro milling Vortex cooling Polymer machining
Acceso en línea:	Acceder al recurso 1 Acceder al recurso 2 Acceder al recurso 3 Acceder al recurso 4 Acceder al recurso 5
Etiquetas:	Agregar Etiqueta Sin Etiquetas, Sea el primero en etiquetar este registro!

Ejemplares similares

Impact of feed rate, milling depth and tool rake angle in peripheral milling of oak wood on the cutting force
por: Marija Đurković
Publicado: (2018)

Estudio comparativo de índices de capacidad de proceso con variables distribuidas no normales
por: Martha Valdiviezo
Publicado: (2010)

An experimental study of heat transfer enhancement using vortex generators in a finned elliptical tube
por: Rubén Borrajo Pérez
Publicado: (2016)

¿TRAIDOR A SU PATRIA? UNITED STATES v. AARON BURR O EL PROCESO A UN FOUNDING FATHER
por: Jorge Pérez Alonso
Publicado: (2011)

Evaluation of the influence of cutting parameters on surface deformation during a milling process.
por: G. Maduro
Publicado: (2015)

A methodological approach to sugar mill diversification and conversion
por: N. Aguilar
Publicado: (2012)

Creation of Computer Aided Manufacturing software from Computer Aided Design software in the milling process
por: JUAN CARLOS CARRASCO GARCÍA
Publicado: (2013)

COMPARISON OF AN ANALYTICAL AND COMPUTATIONAL FLUID DYNAMICS MODELS OF A COMMERCIAL RANQUE-HILSCH VORTEX TUBE OPERATING WITH AIR AND METHANE.
por: Luz Ahumada
Publicado: (2019)

High temperature milling – new method of processing Nd-Fe-B powders
por: W. Kaszuwara
Publicado: (2012)

Feasibility evaluation of two solar cooling systems applied to a cuban hotel. Comparative analysis
por: Yamile Diaz Torres
Publicado: (2016)

DE GENNES PARAMETER DEPENDENCE ON SUPERCONDUCTING PROPERTIES OF MESOSCOPIC CIRCULAR SECTOR
por: JOSÉ JOSÉ BARBA ORTEGA
Publicado: (2012)

Vortex dynamics equation in type-II superconductors in a temperature gradient
por: R. Vega Monroy
Publicado: (2010)

Validação dosimétrica de trabéculas ósseas sintéticas geradas por método Monte Carlo paramétrico
por: F. G. Oliveira
Publicado: (2018)

Impact assessment of intermediate processes of steelmaking in electricity cogeneration of steel mill companies
por: Eder Quental-de-Araújo
Publicado: (2015)

LIDAR ground-based velocity track display analyses and surface observations of a vortex shedding event observed at the Hong Kong International Airport on April 11, 2011
por: P.W. Chan
Publicado: (2017)

Critical Currents and Voltage Oscillations in a Superconducting Sample
por: Cristian Aguirre -Tellez
Publicado: (2024)

Physics-Informed Stacking Ensemble for Simultaneous Prediction of Surface Roughness and Sound Pressure Level in VBD Marble Milling — Dataset and Code
por: Özkan, Erkan, et al.
Publicado: (2026)

Characterization and construction of a compact hammer mill for laboratory use to homogenize natural fibers of Elaeisguineensis and Acrocomia sp.
por: Hazel Aragón
Publicado: (2023)

Operational analysis of electric field mills as lightning warning systems in Colombia
por: D. Aranguren
Publicado: (2011)

Multi-input fuzzy inference system based model to predict the cutting temperature when milling AISI 1060 steel
por: F. Abdelkrim
Publicado: (2023)

Experimental study of flat plate cooling using draft induced by a submerged radial jet
por: Argemiro Palencia-Diaz
Publicado: (2017)

The effect of mesh parameters on computational cost and results in simulation of milling in Inconel 718
por: Felipe dos Anjos Rodrigues Campos
Publicado: (2021)

Design of two bearings with sealing system for the top roll shaft of sugar cane mill
por: Walter Mora Perdomo
Publicado: (2005)

Ground level photosynthetically active radiation dynamics in stands of Acacia mearnsii De Wild
por: SYLVIO PÉLLICO NETTO
Publicado: (2015)

Effects of cutting parameters on surface roughness and hardness in milling of AISI 304 steel
por: Luis Wilfredo Hernández González
Publicado: (2018)

Sorption of copper by olive mill residues
por: Vegliò, F., Beolchini, F., Prisciandaro, M
Publicado: (2003)

Numerical Based Approach for Predicting the Response of Flexible Risers Under Oscillatory Flows at Low Re and KC Numbers
por: M. C. Valencia-Cárdenas
Publicado: (2019)

Growth performance of Chlorella ellipsoidea as biomicrocapsule using supernatant of digested sugar mill waste effluent
por: Parvin, M., et al.
Publicado: (2005)

Vortices in Low-Dimensional Magnetic Systems
por: B. V. Costa
Publicado: (2011)

Bulking in activated sludge plants treating paper mill wastewaters
por: Thompson, G., Forster, C
Publicado: (2003)

Determining cement ball mill dosage by artificial intelligence tools aimed at reducing energy consumption and environmental impact
por: J. R. Gómez Sarduy
Publicado: (2013)

Some toxic constituents of chlorination-stage effluents from bleached kraft pulp mills
por: McKague, A. B
Publicado: (1981)

Boosting the energy output of an On-Grid solar PV system using a novel techniques
por: N. K. Kasim
Publicado: (2023)

Harmonic oscillations of a circular cylinder moving with constant velocity in a quiescent fluid
por: Jan Novaes Recica
Publicado: (2008)

Turbulent mixed flow applying CFD in electronic cooling
por: Carlos Alberto Chaves
Publicado: (2011)

Relative humidity effect on encapsulation properties of coproducts obtained from wet milling of amaranth grain
por: DIEGO-FERNANDO ROA-ACOSTA
Publicado: (2021)

Radon exhalation studies for the remediation of uranium mill tailings ponds in Hungary
por: L. Juhász
Publicado: (2002)

Superconducting Properties of Mesoscopic Squares
por: José J. Barba
Publicado: (2006)

Forced-air, vacuum, and hydro precooling of cauliflower (Brassica oleracea L. var. botrytis cv. Freemont): part I. Determination of precooling parameters
por: Ilknur AlIBAS
Publicado: (2014)

Energy evaluation of an evaporative cooling system using water driven ejector
por: Cíntia Carla Melgaço de OLIVEIRA
Publicado: (2014)