Imagen de Portada

Finite element analysis of a solar collector plate using two plate geometries

Fuente: Redalyc

Guardado en:

Detalles Bibliográficos
Autor principal:	D.M. Medina Carril
Formato:	Artículo científico
Lenguaje:	en
Publicado:	Universidad Nacional de Colombia 2016
Materias:	Ingeniería geometry efficiency Absorber plate solar collector finite element analysis
Acceso en línea:	Acceder al recurso
Etiquetas:	Agregar Etiqueta Sin Etiquetas, Sea el primero en etiquetar este registro!

Ejemplares similares

Entropy generation analysis for the design of a flat plate solar collector with fins
por: Milton Muñoz
Publicado: (2020)

Analysis of absorbed energy and efficiency of a solar flat plate collector
por: Anderson Miguel Lenz
Publicado: (2017)

Numerical analysis of a frontal impact of a 12.7 mm projectile on an armor plate
por: Miloš S. Pešić
Publicado: (2022)

Elastic behavior of stiffened curved plates subjected to transverse loading
por: Abel Noguera Garban
Publicado: (2018)

Performance and determination of Concentration Ratio for a parabolic solar concentrator using a thermographic technique
por: Fabián Cano Ardila
Publicado: (2021)

CFD Analysis of a solar flat plate collector with different cross sections
por: Luis Fernando Toapanta
Publicado: (2020)

Evaluation of stresses and deflections in expanded metal plates subjected to transverse loading
por: José Ángel Matute-Peaspán
Publicado: (2018)

Non-linear analysis of reinforced concrete plates by the boundary element method and continuum damage mechanics
por: Gabriela Rezende Fernandes
Publicado: (2009)

Influence of the patch loading length on the buckling coefficient of longitudinally stiffened plate girders
por: Nelson Loaiza
Publicado: (2019)

Analysis and optimization of the spin beam in the CCA-5000 Cuban sugarcane harvester
por: Roberto Andrés Estrada Cingualbres
Publicado: (2022)

Modelo de elementos finitos para determinar el campo de temperatura en una costura de filete
por: F. Ramos Morales
Publicado: (2007)

Stress analysis in a screw conveyor axis under a specific fault condition
por: Rafael Alfonso Figueroa-Díaz
Publicado: (2019)

Structural health monitoring using the Firefly optimization algorithm and finite elements
por: Octavio Andrés González-Estrada
Publicado: (2020)

Optimizing a mixed water heating system (solar and electric) for rural areas
por: Maurício Medeiros
Publicado: (2013)

Robustness and dispersion analysis of the Partition of Unity Finite Element Method applied to the Helmholtz equation
por: Hervella-Nieto, Luis María, et al.
Publicado: (2019)

Truck Chassis Design and Analysis
por: João Batista De Aguiar
Publicado: (2022)

Machine Learning–Driven Design of Engineered Cilia Enables Hybrid Operations in Acoustic Microrobots
por: Ling, Yun
Publicado: (2026)

A comparative analysis of resistance models for austenitic stainless-steel girders subjected to concentrated loads
por: Carlos Graciano
Publicado: (2022)

Modeling the maximum service load of mobile supports used in the General Rafael Urdaneta bridge
por: Andrés E. Queipo
Publicado: (2015)

Computational simulation of fluid flow by using element based finite volume method on unstructured grids
por: Carlos D. Araujo
Publicado: (2008)

A study of the Hot-Mix Asphalt layer thickness reduction when applied over lateritic soils cement base in airfield
por: Alex Alves Bandeira
Publicado: (2009)

CENTRIFUGAL FAN IMPELLER FAILURE ANALYSIS USING FINITE ELEMENTS
por: Juan Gabriel Monge Gapper
Publicado: (2006)

A static analysis of the tension and configuration of submerged plane nets
por: Wan, R., Hu, F., Tokai, T
Publicado: (2002)

Application of particle swarm optimization in inverse finite element modeling to determine the cornea ́s mechanical behavior
por: Ricardo Magalhães
Publicado: (2017)

Evaluation of surface hardness of NiCr coating using Finite Elements Analysis
por: Lauren Camila Fuentes Rueda
Publicado: (2021)

CFD simulation and validation of flow in small arteries to enable further drug delivery studies
por: Marcela Mercado-Montoya
Publicado: (2020)

Numerical treatment of cosserat based rate independent strain gradient plasticity theories
por: Juan David Gómez C.
Publicado: (2008)

Determination of natural modes of railway overpasses
por: Seidulla S. Abdullayev
Publicado: (2021)

Compressive strength of partially stiffened cylinders at elevated temperatures
por: Egler Araque
Publicado: (2020)

Three-dimensional modeling of pavement with dual load using finite element
por: Wilson Rodríguez-Calderón
Publicado: (2015)

Extension of direct strength method to two dimensional cold formed steel frame
por: P. W. Kubde
Publicado: (2017)

Dynamic test for determining the elastic modulus of coffee fruit-stem-branch system
por: Andre Luiz de Freitas Coelho
Publicado: (2017)

HFFB Test and Wind-Induced Vibration Analysis on 1 000 kV Transformer Frame
por: Wennian Shang
Publicado: (2023)

Analysis of Flow and Heat Transfer in a Flat Solar Collector with Rectangular and Cylindrical Geometry Using CFD
por: Ángel Marroquín-De Jesús
Publicado: (2013)

The mechanical design of a transfemoral prosthesis using computational tools and design methodology
por: J. Sánchez
Publicado: (2012)

A transport modeling of the carbon-nitrogen cycle at Igapó I Lake - Londrina, Paraná State, Brazil
por: Suellen Ribeiro Pardo
Publicado: (2012)

Boundary element analysis for primary and secondary creep problems
por: E. Pineda León
Publicado: (2008)

Development and analysis of a numerical model of the reinforced concrete expansion due to uniform corrosion
por: E. F. Felix
Publicado: (2020)

Aggregation of latex microparticles: simulation and experimental verification
por: Flavio Humberto Fernández Morales
Publicado: (2009)

Numerical and experimental studies of compression-tested copper, mortar contact method
por: Gabriel Jesús Torrente-Prato
Publicado: (2017)