Imagen de Portada

Analysis of broken rotor bars in large induction motors

Fuente: Redalyc

Guardado en:

Detalles Bibliográficos
Autor principal:	Ivan Eduardo Chabu
Formato:	Artículo científico
Lenguaje:	pt
Publicado:	Universidade Nove de Julho 2006
Materias:	Ingeniería Broken bars Fault analysis Induction motor Diagnostic system
Acceso en línea:	Acceder al recurso
Etiquetas:	Agregar Etiqueta Sin Etiquetas, Sea el primero en etiquetar este registro!

Ejemplares similares

The negative sequence impedance as fault indicator in induction motors
por: Fernando Villada
Publicado: (2010)

Improved Energy Conversion Process With Coupling Induction Motors And Invastigate Unbalanced Operation With Definition Of The Voltage Unbalance
por: Hossin Rezaei Koopaei
Publicado: (2015)

ANÁLISE DOS CONTROLES ESCALAR E VETORIAL NO ACIONAMENTO DE MOTORES CA DE BAIXA TENSÃO
por: Canuto, Victor Hugo de Lima, et al.
Publicado: (2025)

Single-neuron adaptive double-power super-twisting sliding mode control for induction motor
por: Siham Mencou, et al.
Publicado: (2025)

An improved direct torque controller applied to an electric vehicle
por: Miguel Durán
Publicado: (2014)

Manufacturing cereal bars with high nutritional value through experimental design
por: Roberta Covino
Publicado: (2015)

Fault Detection in a Heat Exchanger, Comparative Analysis between Dynamic Principal Component Analysis and Diagnostic Observers
por: Juan C. Tudón Martínez
Publicado: (2011)

Preparation of a cereal bar containing bocaiuva: physical, nutritional, microbiological and sensory evaluation
por: Cláudia Leite Munhoz
Publicado: (2014)

Touchless control module for diagnostic images at the surgery room using the Leap Motion system and 3D Slicer Software
por: Andrés Felipe Botero-Ospina
Publicado: (2017)

Synergistic frameworks for sensor fault isolation and accommodation in grid-side converters
por: Mehmood, Faizan, et al.
Publicado: (2024)

Development and characterization of cereal bars made with flour of jabuticaba peel and okara
por: Patrícia Appelt
Publicado: (2015)

Analytical synthesis for four–bar mechanisms used in a pseudo–equatorial solar tracker
por: J. M. González Mendoza
Publicado: (2013)

Fault diagnosis based on multivariate statistical techniques
por: Oscar Camacho
Publicado: (2007)

Agent-based design for fault management system in industrial processes
por: Mariela Cerrada
Publicado: (2006)

Generalised strategy for implementing the minimum fault reactance based fault location algorithm in real power distribution systems
por: E. Correa-Tapasco
Publicado: (2011)

Flatness-based fault tolerant control
por: César Martínez-Torres
Publicado: (2014)

ANALYSIS OF THE BOND STRESS WHEN USING GFRP BARS
por: G M. DALFRÉ
Publicado: (2021)

Carbon nanotube-reinforced aluminum composite produced by induction melting
por: Muhammad Mansoor
Publicado: (2016)

Use of cereal bars with quinoa (Chenopodium quinoa W.) to reduce risk factors related to cardiovascular diseases
por: Flávia Maria Vasques FARINAZZI-MACHADO
Publicado: (2012)

Fault and load flows analysis of electricity transmission and distribution system in Casanare (Colombia)
por: Juan Carlos Castro-Galeano
Publicado: (2017)

The induction generator with two triphases windings in stator
por: Valentin Müller
Publicado: (2006)

Technical brochure - induction welding
por: Wagner, Katharina
Publicado: (2025)

Construcción de identidades: un bar gay en la ciudad de México
por: Rodrigo Laguarda
Publicado: (2005)

Parameter estimation method for induction machines using instantaneous voltage and current measurements
por: Johnny Wladimir Rengifo-Santana
Publicado: (2015)

SOFTWARE FOR FAULT DIAGNOSIS USING KNOWLEDGE MODELS IN PETRI NETS
por: ADRIAN ARBOLEDA
Publicado: (2012)

Manual pr ctico de cafetería y bar / Jesús Felipe Gallego
por: Gallego, Jesús Felipe
Publicado: (2006)

Efficient cooking program in times of COVID-19 in the province of Cotopaxi: energy demand
por: Franklin Israel Sánchez-Gamboa
Publicado: (2021)

The Absolute and Relative Pessimistic Inductions
por: Seungbae Park
Publicado: (2019)

Feedback regulation of a DC motor via interconnection and damping assignment
por: Atilio Morillo
Publicado: (2007)

Raw X-ray fluorescence (XRF) scanning and grain size analysis of ODP Hole 121-752A at Broken Ridge
por: Lyu, Jing, et al.
Publicado: (2023)

A METHODOLOGY FOR KNOWLEDGE MODELING OF FAULT DIAGNOSIS BASED ON PETRI NETS
por: JUAN PALACIO BETANCUR
Publicado: (2013)

Axial Stress Prediction of Torsioned Solid and Hollow Cylindrical Bars
por: Gustavo González
Publicado: (2018)

Morphodynamique d’une plage sableuse microtidale à barres : côte nord de Mahdia (Tunisie orientale)
por: Amrouni, Oula
Publicado: (2008)

Fault location in power distribution systems considering a dynamic load model
por: D. Patiño-Ipus
Publicado: (2015)

HYBRID APPROACH FOR AN OPTIMAL ADJUSTEMENT OF A KNOWLEDGE-BASED REGRESSION TECHNIQUE FOR LOCATING FAULTS IN POWER DISTRIBUTION SYSTEMS
por: EVER CORREA-TAPASCO
Publicado: (2011)

ESTRUCTURA GEOLÓGICA DEL VALLE DE LA CIUDAD DE GUATEMALA INTERPRETADA MEDIANTE UN MODELO DE CUENCA POR DISTENSIÓN
por: Carlos L. Pérez
Publicado: (2009)

Equipment for vehicle classification using inductive loops: an innovative development - (Equipo para la clasificación de vehículos utilizando lazos inductivos: un desarrollo innovador)
por: Guaraglia, Dardo, et al.
Publicado: (2013)

Effect of adhesive replacement with cement mortar on NSM strengthened RC Beam
por: Moshiur Rahman
Publicado: (2016)

Global Fault Current Limiter Market 2025 To 2034
por: Sirsat, Nitin
Publicado: (2025)

Nuevo método para la selección rápida de plantas de banano (Musa spp. AAA cv. Grande naine) transformadas con gen bar procedentes de campo, empleando glufosinato de amonio
por: Rafael Gómez Kosky
Publicado: (2010)