Imagen de Portada

Numerical treatment of cosserat based rate independent strain gradient plasticity theories

Fuente: Redalyc

Guardado en:

Detalles Bibliográficos
Autor principal:	Juan David Gómez C.
Formato:	Artículo científico
Lenguaje:	en
Publicado:	Universidad EAFIT 2008
Materias:	Ingeniería Non couple stress theory constitutive modeling integration algorithms finite element analysis
Acceso en línea:	Acceder al recurso
Etiquetas:	Agregar Etiqueta Sin Etiquetas, Sea el primero en etiquetar este registro!

Ejemplares similares

Stress analysis in a screw conveyor axis under a specific fault condition
por: Rafael Alfonso Figueroa-Díaz
Publicado: (2019)

Structural health monitoring using the Firefly optimization algorithm and finite elements
por: Octavio Andrés González-Estrada
Publicado: (2020)

CENTRIFUGAL FAN IMPELLER FAILURE ANALYSIS USING FINITE ELEMENTS
por: Juan Gabriel Monge Gapper
Publicado: (2006)

CONTACT NOTCH STRESS ASSESSMENT WITHIN FRICTIONAL CONTACT JOINTS
por: DARIUSZ SZWEDOWICZ
Publicado: (2012)

Numerical analysis of a frontal impact of a 12.7 mm projectile on an armor plate
por: Miloš S. Pešić
Publicado: (2022)

Determination of natural modes of railway overpasses
por: Seidulla S. Abdullayev
Publicado: (2021)

Cluster analysis of genetic algorithm results
por: Katarzyna Adamska
Publicado: (2005)

External strengthening of shear deficient beams using AFRP and GFRP Fibers
por: Arya J, et al.
Publicado: (2023)

Modelling and simulation of a thermoelectric waste heat recovery system - TWRHS
por: Anderson Luis Oliveira Maran
Publicado: (2021)

A transport modeling of the carbon-nitrogen cycle at Igapó I Lake - Londrina, Paraná State, Brazil
por: Suellen Ribeiro Pardo
Publicado: (2012)

Analysis and optimization of the spin beam in the CCA-5000 Cuban sugarcane harvester
por: Roberto Andrés Estrada Cingualbres
Publicado: (2022)

Development and analysis of a numerical model of the reinforced concrete expansion due to uniform corrosion
por: E. F. Felix
Publicado: (2020)

Evaluation of stresses and deflections in expanded metal plates subjected to transverse loading
por: José Ángel Matute-Peaspán
Publicado: (2018)

Modelo de elementos finitos para determinar el campo de temperatura en una costura de filete
por: F. Ramos Morales
Publicado: (2007)

Optimization of injection molding process parameters by a hybrid of artificial neural network and artificial bee colony algorithm
por: Alejandro Alvarado Iniesta
Publicado: (2013)

Mechanical characterization of visually graded boards from turkish fir and black pine by nondestructive and destructive tests
por: Fatih Kurul
Publicado: (2024)

Assessment of cohesive traction-separation relationship according stiffness variation
por: Liliana M. Bustamante-Góez
Publicado: (2019)

Finite element analysis of a solar collector plate using two plate geometries
por: D.M. Medina Carril
Publicado: (2016)

Truck Chassis Design and Analysis
por: João Batista De Aguiar
Publicado: (2022)

Mesh and simulation results of multicycle dynamics of the southern San Andreas and the northern San Jacinto faults
por: Dunyu, Liu, et al.
Publicado: (2022)

A study of the Hot-Mix Asphalt layer thickness reduction when applied over lateritic soils cement base in airfield
por: Alex Alves Bandeira
Publicado: (2009)

Machine Learning–Driven Design of Engineered Cilia Enables Hybrid Operations in Acoustic Microrobots
por: Ling, Yun
Publicado: (2026)

Dynamic Analysis of Complex Structures Based on Octree Scaled Boundary Finite Element Method
por: Jamil, Kazi Md Shah, et al.
Publicado: (2026)

A comparative analysis of resistance models for austenitic stainless-steel girders subjected to concentrated loads
por: Carlos Graciano
Publicado: (2022)

Modeling the maximum service load of mobile supports used in the General Rafael Urdaneta bridge
por: Andrés E. Queipo
Publicado: (2015)

A model for coupled electro-hydro-mechanical processes in fine grained soils accounting for gas generation and transport
por: Claudio Tamagnini
Publicado: (2010)

Estimate of induced stress during filling and discharge of metallic silos for cement storage
por: Wilmer Bayona-Carvajal
Publicado: (2015)

Mechanical characterization of jute fiber-based biocomposite to manufacture automotive components
por: J. A. Velasco-Parra
Publicado: (2021)

Numerical and experimental studies of compression-tested copper, mortar contact method
por: Gabriel Jesús Torrente-Prato
Publicado: (2017)

Compressive strength of partially stiffened cylinders at elevated temperatures
por: Egler Araque
Publicado: (2020)

CFD simulation and validation of flow in small arteries to enable further drug delivery studies
por: Marcela Mercado-Montoya
Publicado: (2020)

A static analysis of the tension and configuration of submerged plane nets
por: Wan, R., Hu, F., Tokai, T
Publicado: (2002)

A Fully-Discrete Finite Element Approximation for the Eddy Currents Problem
por: Ramiro Acevedo
Publicado: (2013)

Application of particle swarm optimization in inverse finite element modeling to determine the cornea ́s mechanical behavior
por: Ricardo Magalhães
Publicado: (2017)

HFFB Test and Wind-Induced Vibration Analysis on 1 000 kV Transformer Frame
por: Wennian Shang
Publicado: (2023)

Dynamic test for determining the elastic modulus of coffee fruit-stem-branch system
por: Andre Luiz de Freitas Coelho
Publicado: (2017)

Evaluation of Load Capacity of Stratified Soils (2 Layers) by Means of Numerical Analytical Comparison
por: Jairo-Alejandro Quintero-Chamorro
Publicado: (2021)

Computational simulation of fluid flow by using element based finite volume method on unstructured grids
por: Carlos D. Araujo
Publicado: (2008)

Robustness and dispersion analysis of the Partition of Unity Finite Element Method applied to the Helmholtz equation
por: Hervella-Nieto, Luis María, et al.
Publicado: (2019)

Conceptual design of an alignment device for transfemoral prosthesis
por: Ana Isabel Vásquez
Publicado: (2022)