Image de couverture de livre

Multicale Study of the Fatigue Life of AlSi10Mg Material Produced by Laser Powder Bed Fusion (LPBF) Method: Experimental and Computational

Fuente: Wiley Open Access

Enregistré dans:

Détails bibliographiques
Auteurs principaux:	Kiarash Jamali Dogahe, Tamás Csanádi, Yanling Schneider, Chensheng Xu, Vinzenz Guski, Anindita Dhar Swarna, Jan Dusza, Siegfried Schmauder, Zeljko Bozic, Mahmoud Pezeshki, Mohammad Ridzwan Bin Abd Rahim
Format:	Artículo Open Access
Publié:	Wiley 2025
Sujets:	Fatigue & Fracture of Engineering Materials & Structures
Accès en ligne:	Acceder al recurso
Tags:	Ajouter un tag Pas de tags, Soyez le premier à ajouter un tag!

Documents similaires

On the notch sensitivity of as‐built Laser Beam Powder Bed–Fused AlSi10Mg specimens subjected to Very High Cycle Fatigue tests at ultrasonic frequency up to 109 cycles
par: Andrea Tridello, et autres
Publié: (2024)

Effect of Build Orientation on the Fatigue Limit of CX Steel by Laser Powder Bed Fusion
par: Mattia Mele, et autres
Publié: (2025)

Effect of Laser Scanning Speed on Tensile and Fatigue Behavior of LPBF‐Printed Co‐Cr‐Mo Alloy
par: Vinod Kumar Jat, et autres
Publié: (2025)

On the Growth of Small Cracks in 2024‐T3 and Boeing Space, Intelligence and Weapon Systems AM LPBF Scalmalloy®
par: R. Jones, et autres
Publié: (2024)

Strain Field Visualization During Fatigue Crack Growth in Microstructure Tailored LPBF Ti‐6Al‐4V
par: Roger Beal, et autres
Publié: (2025)

Effect of Heat Treatment on the Fatigue of Laser‐Powder Bed Fused Ti‐6Al‐2Sn‐4Zr‐2Mo Alloy
par: Harish Chandra Kaushik, et autres
Publié: (2025)

Synergistic Improvement of Fatigue Performance in Laser Powder Bed Fusion 316L Steel Through Heat Treatment and Low‐Temperature Gaseous Carburizing
par: Yajian Feng, et autres
Publié: (2025)

Rotating Bending Fatigue of Laser Powder Bed Fused 316L Stainless Steel at Various Stress Levels: Microstructural Evaluation and Predictive Modeling
par: Yahya Aghayar, et autres
Publié: (2024)

Fatigue Assessment of Precorroded AlSi9Cu3 Specimens Incorporating Short Crack Propagation
par: Peter Oberreiter, et autres
Publié: (2025)

Effect of corrosion pit on fatigue damage and failure in powder bed fusion AlSi10Mg
par: Haipeng Song, et autres
Publié: (2024)

Fatigue life prediction of additively manufactured AlSi10Mg based on surface roughness and residual stress
par: Lea Strauß, et autres
Publié: (2024)

Fatigue and Fracture Behavior in Advanced Layer‐Level SS316L‐17‐4PH Multi‐Material Fabrication via Powder Bed Fusion—Laser Beam
par: Vito Errico, et autres
Publié: (2025)

Fatigue Behavior and Life Prediction of Additively Manufactured AlSi10Mg up to 108 Cycles Under Rotating Bending
par: Zhonghua Jiang, et autres
Publié: (2025)

Predicting the Size‐Dependent Fatigue Strength Distributions in Additively Manufactured AlSi10Mg Alloy Specimens Using Extreme Value Statistics
par: Tomasz Tomaszewski, et autres
Publié: (2026)

Experimental and Numerical Simulation Study on the Influence of Bedding Angle on the Blasting Effect of Slotted Charges
par: Jun Zhou, et autres
Publié: (2026)

Dynamic Fracture Characteristics of Layered Rock Mass With Two Beddings Under Explosive Loads of Slotted Charges
par: Xu Wang, et autres
Publié: (2025)

Investigation of Crystallographic Influences on Small Fatigue Crack Growth in Powder Metallurgy Superalloy FGH96
par: Guo Li, et autres
Publié: (2025)

Fatigue Performance of S460 High-Strength Steel Welded Joints: Experimental and Numerical Approaches
par: Al Khazali, Mohammad Sami, et autres
Publié: (2025)

Creep Behavior and Fracture Mechanisms of the Dissimilar Inertia Friction Welded Joints of Deformed and Powder Metallurgy Ni‐Based Superalloys
par: Zixin Zhang, et autres
Publié: (2024)

Corrosion and Fatigue Behavior of Boeing Space, Intelligence, and Weapons Systems Laser Powder Fusion Built Scalmalloy® in 5% NaCl
par: Andrew Ang, et autres
Publié: (2025)

AI.LC-Analyzer – Technical Documentation V9.46. - Phase 1: A mechanistic system architecture for trajectory-based analysis of chronic disease dynamics
par: Fuerste, Dietmar
Publié: (2026)

EFFECT OF THE FAILURE CRITERION ON THE LABORATORY FATIGUE RESPONSE PREDICTION OF HOT-MIX ASPHALT MIXTURES
par: OSCAR J. REYES-ORTIZ
Publié: (2012)

Proposition of a human fatigue risk management computational tool for Air Traffic Controllers
par: Rodrigo Pereira Gomes
Publié: (2025)

Evaluation of moisture‐induced damage on the fatigue life of asphalt mixtures using failure tests of asphalt binders, interfaces, and mixtures
par: Lucas Sassaki Vieira da Silva, et autres
Publié: (2024)

Influence of Low‐Velocity Impact Damage on Residual Strength and Fatigue Behavior of GFRP Composites
par: P. Karthick, et autres
Publié: (2025)

Thickness Effects on Distributed Backface Strain Sensing of Adhesively Bonded Joints Under Mixed Mode Fatigue Loading
par: Alessandra Panerai, et autres
Publié: (2025)

In‐Service Inspection Optimization for Pressurized Water Reactor Primary Piping Weld Based on Probabilistic Fracture Mechanics
par: Zhenshun Liu, et autres
Publié: (2025)

Examination of Fatigue Characteristics of Carburized Steel Under Axial Loading Using Large Dataset
par: Shogo Takesue, et autres
Publié: (2026)

Guest Editorial of Virtual Special Issue: Artificial Intelligence‐Assisted Fatigue Prediction of Engineering Materials and Structures
par: Haohui Xin, et autres
Publié: (2024)

Multiaxial Creep Rupture Life Evaluation for Austenitic Stainless Steels Using Weld‐Type Miniature Cruciform Specimen
par: Noritake Hiyoshi, et autres
Publié: (2026)

A Novel Multiaxial High‐Cycle Fatigue Life Prediction Model Based on Critical Plane‐Intrinsic Damage Dissipation
par: Zhongkai Ren, et autres
Publié: (2025)

Proposing a New Crack Driving Force Parameter for Fatigue Crack Growth Rate of C–Mn Steel
par: Prakash Bharadwaj, et autres
Publié: (2025)

Evolution of Mechanical Behaviors, Consolidation and Failure Mechanisms in Sandstone Materials Under Compressive Stress: The Role of Chemical Remediation Cycles
par: Jun Li, et autres
Publié: (2026)

Estimating crack tip position in adhesively bonded joints subjected to mode II quasi‐static loading
par: M. Mehrabi, et autres
Publié: (2024)

A PINN–XGBoost Hybrid Model for High‐Cycle Fatigue Life Prediction of Mg Alloy Welded Joints
par: Haili Sun, et autres
Publié: (2026)

Fatigue Life Prediction of LF6 Aluminum Alloy Laser‐Arc Hybrid Welded Joints Based on Energy Dissipation Method
par: Chengji Mi, et autres
Publié: (2024)

Low‐Cycle and Thermomechanical Fatigue Life Prediction Method for Compacted Graphite Iron Based on Small‐Sample Physics‐Informed Neural Networks
par: Teng Ma, et autres
Publié: (2025)

Review on Optimization of Tensile, Fatigue, and Creep Properties of Additive Manufactured Nickel‐Based Superalloys by Modifying the Microstructure and Residual Stress
par: Xinming Lei, et autres
Publié: (2025)

Torsional Mechanical Behavior of TPMS Porous Structures: Experimental Insights on Diamond, Gyroid, and Schwarz Primitive Designs
par: Yiqun Hu, et autres
Publié: (2025)

Fatigue Life Analysis and Experimental Study of a Broadband Non‐Stationary Stochastic Process With Mean Stress
par: Yuhao Zhu, et autres
Publié: (2025)