Imagen de Portada

Вестник Дагестанского государственного технического университета: Технические науки

Fuente: DOAJ

Guardado en:

Detalles Bibliográficos
Formato:	Revista científica
Lenguaje:	RU
Publicado:	Dagestan State Technical University 2017
Materias:	bearing layer building enterprise deformation finite element method heat transfer Technology T
Acceso en línea:	Acceder al recurso
Etiquetas:	Agregar Etiqueta Sin Etiquetas, Sea el primero en etiquetar este registro!

Ejemplares similares

MPM and ALE simulations of large deformations geotechnics instability problems
por: Giovanna Monique Alelvan
Publicado: (2020)

Development of a C Program for Thermal and Structural Analysis in Die Casting Processes
por: Raju Panchal
Publicado: (2025)

Temperature distributions in pavement and bridge slabs heated by using vertical ground-source heat pump systems
por: Asim Balbay
Publicado: (2013)

Elastic behavior of stiffened curved plates subjected to transverse loading
por: Abel Noguera Garban
Publicado: (2018)

Saline distribution during multicomponent salting in pre-cooked quail eggs
por: Dionísio BORSATO
Publicado: (2012)

Vibration Analysis of Rolling Element Bearings Defects
por: H. Saruhan
Publicado: (2014)

Modelling and simulation of a thermoelectric waste heat recovery system - TWRHS
por: Anderson Luis Oliveira Maran
Publicado: (2021)

Solution of the Inverse Bio-Heat Transfer Problem for a Simplified Dermatological Application: Case of Skin Cancer
por: José Manuel Luna
Publicado: (2014)

Optimal ratios of the piston speeds for a finite speed endoreversible Carnot heat engine cycle
por: Huijun Feng
Publicado: (2010)

Вестник Донского государственного технического университета
Publicado: (2018)

Effect of heat transfer on the performance of a thermoelectric heat pump driven by a thermoelectric generator
por: Lingen Chen
Publicado: (2009)

Axisymmetric modelling of transient thermal response in solids for application to infrared photothermal radiometry technique
por: J. Hernández-Wong
Publicado: (2019)

Ecological performance optimization of a thermoacoustic heat engine
por: Lingen Chen
Publicado: (2010)

Experimental behavior of a masonry wall supported on a RC twoway slab
por: Alonso Gómez-Bernal
Publicado: (2015)

Boundary element analysis for primary and secondary creep problems
por: E. Pineda León
Publicado: (2008)

A transport modeling of the carbon-nitrogen cycle at Igapó I Lake - Londrina, Paraná State, Brazil
por: Suellen Ribeiro Pardo
Publicado: (2012)

Dynamic test for determining the elastic modulus of coffee fruit-stem-branch system
por: Andre Luiz de Freitas Coelho
Publicado: (2017)

Analytical Heat Transfer
por: Han, Je-Chin, et al.
Publicado: (2023)

A coupled virtual element-interface model for analysis of fracture propagation in polycrystalline composites
por: Gatta, Cristina, et al.
Publicado: (2024)

Aggregation of latex microparticles: simulation and experimental verification
por: Flavio Humberto Fernández Morales
Publicado: (2009)

Application of the factorial design and finite element methods to optimize the solidification of Cu-5wt%Zn alloy in a sand mold
por: M.M. Pariona
Publicado: (2008)

A static analysis of the tension and configuration of submerged plane nets
por: Wan, R., Hu, F., Tokai, T
Publicado: (2002)

Development and analysis of a numerical model of the reinforced concrete expansion due to uniform corrosion
por: E. F. Felix
Publicado: (2020)

Multicomponent diffusion during Prato cheese ripening: mathematical modeling using the finite element method
por: Evandro BONA
Publicado: (2010)

Deflexión en arcos usando métodos energéticos
por: Miranda Casazola Dayan Esmirna
Publicado: (2020)

Evaluation of Load Capacity of Stratified Soils (2 Layers) by Means of Numerical Analytical Comparison
por: Jairo-Alejandro Quintero-Chamorro
Publicado: (2021)

Robustness and dispersion analysis of the Partition of Unity Finite Element Method applied to the Helmholtz equation
por: Hervella-Nieto, Luis María, et al.
Publicado: (2019)

CONTACT NOTCH STRESS ASSESSMENT WITHIN FRICTIONAL CONTACT JOINTS
por: DARIUSZ SZWEDOWICZ
Publicado: (2012)

Influence of damping ratio on a structural optimization design considering a dynamic analysis within the time domain
por: Débora Francisco Lalo
Publicado: (2018)

Study of the behavior of a reinforced embankment supported on alluvial soft soil
por: João Alexandre Paschoalin Filho
Publicado: (2013)

ADVANCING PROBABILISTIC FRAME ANALYSIS: A COMPREHENSIVE APPROACH USING MONTE CARLO SIMULATION AND RESPONSE SURFACES
por: Wilson Rodríguez-Calderón
Publicado: (2024)

Global optimization algorithms applied in a parameter estimation strategy
por: David Matajira-Rueda
Publicado: (2018)

Composite materials reinforced with ceramic waste and matrix of unsaturated polyester for applications in the automotive industry
por: Jorge Antonio Velasco-Parra
Publicado: (2020)

Mechanical characterization of visually graded boards from turkish fir and black pine by nondestructive and destructive tests
por: Fatih Kurul
Publicado: (2024)

An Analysis of Total Phosphorus Dispersion in Lake Used As a Municipal Water Supply
por: RÔMULO C. LIMA
Publicado: (2015)

Analysis of the use of aluminum pipes for irrigation as an electrical conduit for an underground installation
por: Josnier Ramos Guardarrama
Publicado: (2023)

Effect of longitudinal stiffening on bridge girder webs at incremental launching stage
por: C. A. Graciano
Publicado: (2015)

International Journal of Advanced Design and Manufacturing Technology
Publicado: (2023)

Journal of Heat and Mass Transfer Research
Publicado: (2024)

Estimating fan and pad greenhouse reference evapotranspiration using FAO-56 - Penman-Monteith and a simplified heat transfer approach for predicting internal temperature
por: Gaafer, Amna Mohammed El Amin, et al.
Publicado: (2024)